abrasive material
英 [əˈbreɪsɪv məˈtɪəriəl]
美 [əˈbreɪsɪv məˈtɪriəl]
磨料
英英释义
noun
双语例句
- A set of construction procedure has been made based on RS-9 insulating liner material and RS-17E abrasive liner material which are used in catalytic cracking equipments of petrochemical plants. It points out notices for each process and ensures construction quality.
针对美国RESCO公司隔热衬里材料RS9和耐磨衬里材料RS17E用于石油化工厂催化裂化装置制定了一整套施工程序，提出了各工序的注意事项，从而确保了施工质量。 - With the orthogonal tests the influence of work condition of the 3-phase abrasive water jet to material removal and erosion depth is analyzed, and the relationship between the abrasive granularity and the surface roughness is discussed.
通过正交试验，分析了三相射流工作条件对材料去除量和冲蚀深度的影响，讨论了磨料粒度与加工表面粗糙度的关系。 - For the two kinds of abrasive grain& ordinary abrasive and ultra hard material, carborundum and diamond were chosen as samples for dispersing experiment.
针对两大类磨料微粉&普通磨料和超硬材料，选择碳化硅和金刚石为例进行分散实验。 - The wear mechanism of the friction pair involved abrasive wear and material loss on surface layer resulted from UHMWPE plastic deformation.
摩擦副的主要磨损机理为磨粒磨损及UHMWPE塑变导致的表层材料损失。 - Black Aluminium Oxide AbrasiveBlack aluminium oxide abrasive ( lower aluminium oxide abrasive) is a new type abrasive material for polishing various metal.
黑刚玉砂（又名低铝刚玉砂、铁砂粉）是种新型抛光材料。以三水型和一水型铝矾土为原料经电弧炉高温冶炼冷却而成。 - It is performed through the verification and analysis of the interrelation of typical materials cutting features ( cutting depth, kerf width, striking capacity) and cutting variables ( water pressure, target distance, cutting rate and so on) and the effeCts of abrasive and material.
验证分析了典型材料的切割特征（切割深度、切口宽度、冲蚀量）与切割变量（水压、靶距、切速等）的关系，以及磨料、材质两大因素的影响。 - Brown fused alumina abrasive is the most widely used artificial abrasive grinding material has a certain importance in world economic development and strategic.
棕刚玉磨料是人造研磨材料中最为广泛应用的一种研磨材料，在世界经济发展中具有一定的重要性和战略性。 - Preparation and properties of up/ al_2o_3 composite for particulate abrasive material
UP/Al2O3复合微粒磨料的制备和性能研究 - According to the working condition of high temperature and abrasive wear, the material structure and composition of the wear-resistant and heat-resistant steel are designed.
根据在高温氧化性气氛下磨料磨损的工况条件，合理设计了抗磨耐热钢材料的组织和化学成分。 - The test results show that wear resistance of tested steel under low stress abrasive depends on material hardness. Wear resistance of quenched microstructure is highest.
结果表明：低应力磨粒磨损的耐磨性主要取决于材料的硬度，淬火态组织的耐磨性最好。